 |
|
 |
|
Next: Trails Around San Antonio, TX
|
| Author |
Message |
External

Since: Jun 25, 2003 Posts: 136
|
(Msg. 1) Posted: Wed Jan 28, 2004 4:28 am
Post subject: FS: '01 XR400, Colorado Springs Archived from groups: rec>motorcycles>dirt (more info?)
|
|
|
Well, I hate to do it, but I have to right now. Money's tight, I can't ride
right now because of a bad back, and I can always get another when I get a job.
This economy sux. Bike is in Colorado Springs. The following are mods,
accessories, and new parts ( the new parts below were put on in November '03,
and have been used only once for a 6 mile ride):
Mods:
Top of airbox cut out
TwinAir Filter & cage(new)
Header welds ground to 1"
FMF PowerCore4Q Exhaust
Renthal bars, stock bend
Stickers to make it go faster
Accessories:
Moose alum. skid plate
Maier alum. barkbusters
One Ind. tank/swingarm graphix
EnduroEngineering steel shark fin
New Parts:
MSR Raptor clutch perch w/ easy-pull lever
Clutch cable
Brake lever
Brake pads, front & rear
ProGrip grips
Brake fluid, f & r
Renthal chain (non-o-ring)
Renthal 14T CS, 48T rear
Front tire has maybe 20 miles on it, rear probably 125
Acerbis front disk guard
10 miles on last oil change
Asking $3500. If you think it's too much, come down and ride it.
--Chris M.
(Unemployed...for now) >> Stay informed about: FS: '01 XR400, Colorado Springs |
|
| Back to top |
|
 |  |
External

Since: Sep 05, 2003 Posts: 1068
|
(Msg. 2) Posted: Wed Jan 28, 2004 4:28 am
Post subject: Re: FS: '01 XR400, Colorado Springs [Login to view extended thread Info.] Archived from groups: per prev. post (more info?)
|
|
|
Sounds very nicely set up. Good luck.
Mike
On 28 Jan 2004 03:28:17 GMT, wudscrasher DeleteThis @aol.com (Wudscrasher) wrote:
>Well, I hate to do it, but I have to right now. Money's tight, I can't ride
>right now because of a bad back, and I can always get another when I get a job.
> This economy sux. Bike is in Colorado Springs. The following are mods,
>accessories, and new parts ( the new parts below were put on in November '03,
>and have been used only once for a 6 mile ride):
>
>Mods:
>Top of airbox cut out
>TwinAir Filter & cage(new)
>Header welds ground to 1"
>FMF PowerCore4Q Exhaust
>Renthal bars, stock bend
>Stickers to make it go faster
>
>Accessories:
>Moose alum. skid plate
>Maier alum. barkbusters
>One Ind. tank/swingarm graphix
>EnduroEngineering steel shark fin
>
>New Parts:
>MSR Raptor clutch perch w/ easy-pull lever
>Clutch cable
>Brake lever
>Brake pads, front & rear
>ProGrip grips
>Brake fluid, f & r
>Renthal chain (non-o-ring)
>Renthal 14T CS, 48T rear
>Front tire has maybe 20 miles on it, rear probably 125
>Acerbis front disk guard
>10 miles on last oil change
>
>Asking $3500. If you think it's too much, come down and ride it.
>
>--Chris M.
>(Unemployed...for now)
--
Yours respectfully,
Robert Falcon Scott
N42d 07.084'
W72d 22.344'
"Had we lived, I should have had a tale to tell of the hardihood,
endurance, and courage of my companions which would have stirred the heart
of every Englishman. These rough notes and our dead bodies must tell the
tale."
00 Kohler-driven Snow-Fighter
96 XR400
74 CZ250 Enduro
99 KZ1000P
BRC, AMA, NETRA, NOHVCC, NRA<!-- ~MESSAGE_AFTER~ --> >> Stay informed about: FS: '01 XR400, Colorado Springs |
|
| Back to top |
|
 |  |
External

Since: Sep 19, 2003 Posts: 428
|
(Msg. 3) Posted: Wed Jan 28, 2004 5:57 am
Post subject: Re: '01 XR400, Colorado Springs [Login to view extended thread Info.] Archived from groups: per prev. post (more info?)
|
|
|
"Wudscrasher" <wudscrasher.DeleteThis@aol.com> wrote in message
news:20040127222817.24788.00000851@mb-m16.aol.com...
> Well, I hate to do it, but I have to right now. Money's tight, I can't
ride
> right now because of a bad back, and I can always get another when I get a
job.
Meooooooooowwwww-<Crack!>
Sorry dude, just giving you a hard time. Good luck down there.
Sorry we didn't get to hook up this weekend. I was working
anyway.
-Jeffrey Deeney- DoD#0498 NCTR UTMA BRC COHVCO AMA
'99 ATK 260LQ-Stink Wheels '94 XR650L-DreamSickle
We don't stop riding because we get old, we get old because we stop riding.<!-- ~MESSAGE_AFTER~ --> >> Stay informed about: FS: '01 XR400, Colorado Springs |
|
| Back to top |
|
 |  |
| Related Topics: | xr400 fork gurus?? - I have a 2000 XR400 that I bought used and I am trying to dial in the front fork suspension. I am a novice at anything mechanical on these toys, but I use the manuals and stick with it. The previous owner installed a 44 kg race tech spring set (I have..
WANTED: Kayaba 46mm Fork Springs - If any one has a set in great shape I'm looking for YZ250 46mm Kayaba fork springs. 41.2mm ID X 469mm. in the .43 or .44kg/mm rate. Thanks, Jim www.cannondaler.com jschnerDELETTHIS@charter.net
FS: '99 KLX300R & Extras *PICS* $2400 - Posted for friend. Send email to work_NOSPAMlog@yahoo.com (Remove NOSPAM to send email) 1999 KLX300R, Very Low Hours $2400 Delivered Stroker: Shift Star, Idler Gear, Head Pipe, SX-1 Muffler, Fresh Dunlop D756 Tires (1st set of tires!), Renthal Bars...
Hebo Hydraulic Clutch Kits - Anybody got an online source for purchasing these? as I can't get them in NZ. Cheers
Am I a heathen - Ok Here is the problem. 3 months ago just prior to the Washougal Nat'l, I won a DRZ110 in raffle. I had been looking for a used bike that size for several months for my two young daughters. I race the vet class and my girls wanted to give MX a shot. Well... |
|
You can post new topics in this forum You can reply to topics in this forum You can edit your posts in this forum You can delete your posts in this forum You can vote in polls in this forum
|
|
|
|
 |
|
|